Author: admin

In the Dutch Renault forum, the issue came up that the maximum regenerative power allowed is higher than what CanZE reports as the Max battery charge / regen kW power. Based on a few experiments of my own only, it seems the Zoe will allow double the reported power for regeneration, capped at 40 kW DC of course. After all, it is supposed to be a short burst and the amount of energy, by definition, has already been taken from the battery.

I would appreciate your findings. Just open CanZE on the driving screen and whenever the Max battery charge / regen kW is substantially below 20 kW, try to do a serious regenerative brake (from a high speed works best, i.e. a motorway exit) and see how far the DC Power kW (or if it refreshes too slow, the blue kW in the dash) shows please. Thank you!

Edit: based on my own testing it seems there is indeed a short over-power possible. The rough formula is max_charge_power * 1.65 + 3.5. More testing by Borut suggests this seems sustainable for either roughly 40 seconds, or until the total battery voltage reaches 390 volts (4.06 volts per cell), see the comments.

It should be possible to calculate the max regen power by taking the max_regen_torque (the blue bar in the driving and consumption screen) and multiply that by the wheel speed (in rad/sec). I might implement this in a test screen.

The Zoe has a crawling mode that cannot be disabled (which is unfortunate I think, but I know others differ). It needs a bit of braking to counter this crawling when at a traffic light. When the brake pedal is pressed only a bit, the motor will still push and you’re spoiling a couple of hundred watts in the motor. So, when at a red light, either press the brake a bit firm, or switch the gear to N.

The R240 is the Zoe with the new, more efficient, air-cooled motor that Renault developed in-house. There is some consensus that the battery of the R240 is exactly the same as the Q210, but given the different characteristics of the motor, and the fact that the motor coils are used by the charger (very smart design!) it is capped to charge at a rate of 22 kW maximum. A UK based Zoe driver noticed the “Max battery charge” nicely went up way above 22 kW and asked how that could be.

Today, user Crf supplied us with this CanZE graph when charging his R240 at a 43 kW charger, and I believe it confirms what we were thinking. The Zoe simply caps the incoming pilot and fakes it’s value towards the other systems involved. Notice how it reports 32A and 22 kW available power. Those numbers are both off and way too neatly rounded.

The battery itself (the LBC’s) reports it’s willingness to take the full 40 kW DC power load, and as the SOC goes up it starts it’s capping at roughly 11 kWh. Again, the little jumps we believe is caused by the temperature rising. 2 kWh per degree Celsius is ballpark right. The very rapid capping near the end is kinda interesting.

So yes, it seems like the R240 has the same battery as the Q210. The BCB is tweaked a bit to simply ignore anything above 22 kW and the rest of the car simply behaves as if a 22 kW charger is attached.

I would be interested if any of you have a screen shot of a charging graph where an R240 is being charged at a 43 kW charger, preferably starting at a low SOC (30% or lower). Your help is much appreciated.

So, loosing that little shelf for the dongle was a bit annoying right? Here is what I did. First, get yourself an ultra-flat OBD2 extension cable, such as this one www.ebay.com.au/itm/181765630282. You also need two RJ-45 connectors, an RJ-45 connection block and a crimp tool for the connectors.

Now that male plug is still not flat enough to fit under the shelf, so carefully shave off it’s top like this. Also, cut the cable 10 cm from the female end and crimp RJ-45 connectors on both ends, fitting the colors of the strands in the same sequence in both RJ-45 connectors. Be wise and check if the dongle still works with the two ends connected through the block before continuing.

Next, widen the hole so a standard RJ-45 connector can be pushed through.

Push a piece of stiff electical wire through to either side of the console. It works best if you pry the plastic of the console a bit away from the carpet.

Use the electrical wire to pull the long part of the extension cable (with the male connector) through from the top, RJ-45 end first. Because of the locking clip of the RJ-45, this will be a once-only operation, unless you are prepared to widen that hole substantially more. Or simply cut the wire at the RJ-45 end when you need to remove it. Connect the two parts using the connection block. Finally, push the dongle into the female end of the now rejoined extension cable.

Connect the male end to the car’s SAE 1962 connector and carefully wrap the cable so it won’t push up the shelf. Check again if everything works.

Reseat the shelf.

I tucked the cable under the console. I like this setup, as I can switch it off. Of course you can put it elsewhere or even hide it entirely if you don’t care about switching it off (you should care!).

Done!

PS: Later on (no picture) I moved the dongle a lot more to the aft side. That got it out of the way of careless feet, and because of the shape of the floor it is pushed flush against the console instead of sticking out like you can see in the picture. Finally, it makes the LED’s far easier to see. Much better.