Comments on: Dongle tester app https://canze.fisch.lu/2017/12/03/dongle-tester-app/ Sat, 05 Aug 2023 06:48:44 +0000 hourly 1 https://wordpress.org/?v=6.6.2 By: ZoeDoktor https://canze.fisch.lu/2017/12/03/dongle-tester-app/#comment-633 Wed, 06 Dec 2017 20:52:18 +0000 http://canze.fisch.lu/?p=1511#comment-633 Reinstalling CanZE did not help.
Same results also from the new black Konwei.
“AT CRA 699” and “AT MA” commands made ZOE Can-Bus provide data lines.

]]> By: ZoeDoktor https://canze.fisch.lu/2017/12/03/dongle-tester-app/#comment-632 Wed, 06 Dec 2017 19:24:28 +0000 http://canze.fisch.lu/?p=1511#comment-632 I just did your wounderful command prompt dongle test sequence. My green Konwei passed everthing and reported every second a line on the “at ma” command. ! I will reinstall my CanZE now.

]]> By: ZoeDoktor https://canze.fisch.lu/2017/12/03/dongle-tester-app/#comment-631 Wed, 06 Dec 2017 15:21:31 +0000 http://canze.fisch.lu/?p=1511#comment-631 Thank you for the response.

I did hours of testing with the two dongles now. In the newer dongle I cut the 120 Ohm resistor yesterday already.

With android “ELM327 OBD Terminal” I communicated with the dongles. I did find out that protocolls 6 and 7 work with the ZOE Can bus.
Protocol 6: ISO 15765-4 (11 bit, 500 kBaud).

But: “no data” reported after the “01 00” OBD command, and others too. Even when I did set the timeout via command: “AT ST FF” to the maximum.

Finally using CanZE again. Good bluethooth connection, but not data transmitted. “ELM327 Dongle” test reports always this 2 lines:

“Please wait until the poller thread has stopped a S^

No connection. Please close this screen and check the connection”

————————
Next steps:
1) Buy an original ELM chip dongle, at 65 pounds in the UK, software 2.2. ?
https://www.scantool-direct.co.uk/genuine-elm327-chip-scan-tool-obdii-eobd-bluetooth-diagnostic-interface.html

2. Test my dongles in another ZOE, perhaps my CAN-bus wiring has some peculiarity.

KR, Franz

]]> By: Jeroen Meijer https://canze.fisch.lu/2017/12/03/dongle-tester-app/#comment-630 Tue, 05 Dec 2017 22:18:59 +0000 http://canze.fisch.lu/?p=1511#comment-630 PS: I forgot to mention: Not sure about Torque, but Torque Light is absolutely useless on ZOE, it will not be able to connect whatsoever as it hunts for ECU’s the ZOE does not have. You know, engine control 😉

]]> By: Jeroen Meijer https://canze.fisch.lu/2017/12/03/dongle-tester-app/#comment-629 Tue, 05 Dec 2017 22:15:13 +0000 http://canze.fisch.lu/?p=1511#comment-629 The new designs KONNWEI 902 report MAC address FF:FF:FF:FF:FF:FF which is nasty when switching between dongles, but they actually work fine (as long as you don’t have two). It’s stupid but no hoax. Note that this model also had the resistor problem. If I were you I would check that problem first before focusing on the FF’s. But that’s my opinion of course.

]]> By: ZoeDoktor https://canze.fisch.lu/2017/12/03/dongle-tester-app/#comment-628 Mon, 04 Dec 2017 15:46:49 +0000 http://canze.fisch.lu/?p=1511#comment-628 This is definitely a bad clone: weird MAC address: FF: all the way:

———————

Scan datum=2017-12-04 11:04:45
Geräte name=KONNWEI
Geräte mac=FF:FF:FF:FF:FF:FF
Die Geräte version (deklariert)=ELM327 v1.5

Befehl Version Ergebnis
AT@1 1.0 OK
ATSPA6 1.0 OK
ATTPA6 1.0 OK
ATTP6 1.0 OK
ATSP00 1.3 OK
ATSP6 1.0 OK
ATAL 1.0 OK
ATNL 1.0 OK
ATAMC 2.0 KO
ATAMT20 2.0 KO
ATRA70 1.3 OK
ATSR70 1.2 OK
ATAR 1.2 OK
ATAT0 1.2 OK
ATAT2 1.2 OK
ATAT1 1.2 OK
ATBD 1.0 OK
ATBRT0F 1.2 OK
ATCAF0 1.0 OK
ATCAF1 1.0 OK
ATCEA04 1.4 OK
ATCERF1 2.2 KO
ATCEA 1.4 OK
ATCF00000111 1.0 OK
ATCF111 1.0 OK
ATCFC0 1.0 OK
ATCFC1 1.0 OK
ATCM00000111 1.0 OK
ATCM111 1.0 OK
ATCP18 1.0 OK
ATCRA7C0 1.3 OK
ATCRA000007C0 1.3 OK
ATCRA 1.4b KO
ATCS 1.0 OK
ATCSM0 1.4b KO
ATCSM1 1.4b KO
ATCTM5 2.1 KO
ATCTM1 2.1 KO
ATCV0000 1.4 OK
ATD1 1.3 OK
ATD0 1.3 OK
ATDP 1.0 OK
ATDPN 1.0 OK
ATE0 1.0 OK
ATE1 1.0 OK
ATFCSD0430FF00 1.1 OK
ATFCSH000007B0 1.1 OK
ATFCSH7B0 1.1 OK
ATFCSM0 1.1 OK
ATFE 1.3a OK
ATH0 1.0 OK
ATH1 1.0 OK
ATI 1.0 OK
ATIB10 1.0 OK
ATIB12 2.2 KO
ATIB15 2.2 KO
ATIB48 1.4 OK
ATIB96 1.0 OK
ATIFRS 1.2 OK
ATIFRH 1.2 OK
ATIFR0 1.2 OK
ATIFR2 1.2 OK
ATIFR1 1.2 OK
ATIFR6 2.2 KO
ATIFR5 2.2 KO
ATIFR4 2.2 KO
ATIGN 1.4 OK
ATIIA7A 1.2 OK
ATJS 1.3 OK
ATJE 1.3 OK
ATJHF0 1.4b KO
ATJHF1 1.4b KO
ATJTM5 1.4b KO
ATJTM1 1.4b KO
ATKW 1.3 OK
ATKW0 1.2 OK
ATKW1 1.2 OK
ATL0 1.0 OK
ATL1 1.0 OK
ATM1 1.0 OK
ATM0 1.0 OK
ATPPFFON 1.1 OK
ATPPFFOFF 1.1 OK
ATR0 1.0 OK
ATR1 1.0 OK
ATRV 1.0 OK
ATS0 1.3 OK
ATS1 1.3 OK
ATSDFF 1.4 OK
ATRD 1.4 OK
ATSH000007E0 2.0 KO
ATSHA848F1 1.0 OK
ATSH7B0 1.0 OK
ATST32 1.0 OK
ATSWFF 1.0 OK
ATTAF9 1.4 OK
ATV1 1.3 OK
ATV0 1.3 OK
ATWMC133F13E 1.0 OK
ATPC 1.0 OK
ATWS 1.0 OK
ATD 1.0 OK
ATZ 1.0 OK

]]> By: ZoeDoktor https://canze.fisch.lu/2017/12/03/dongle-tester-app/#comment-627 Mon, 04 Dec 2017 13:30:14 +0000 http://canze.fisch.lu/?p=1511#comment-627 sorry. I did mean I use CanZE also. But there the same dysfunctionality. … and my comments in August show, my ZOEs OBD works with iCar Soft tool without problems.

]]> By: ZoeDoktor https://canze.fisch.lu/2017/12/03/dongle-tester-app/#comment-626 Mon, 04 Dec 2017 13:27:46 +0000 http://canze.fisch.lu/?p=1511#comment-626 yes, also.
In CanZE the ELM test reports that it cannot connect., although it reports that is is connected .
No data are transmitted actually from the car.

]]> By: Bob Fisch https://canze.fisch.lu/2017/12/03/dongle-tester-app/#comment-625 Mon, 04 Dec 2017 12:14:38 +0000 http://canze.fisch.lu/?p=1511#comment-625 In reply to ZoeDoktor.

But do they work with CanZE?

]]> By: ZoeDoktor https://canze.fisch.lu/2017/12/03/dongle-tester-app/#comment-624 Mon, 04 Dec 2017 11:17:05 +0000 http://canze.fisch.lu/?p=1511#comment-624 So do mine two I have. A black one, arriving yesterday and an older green one.

Both signal 1.5 but produce exactly the same protocolls versions ending at 1.4.

One even has a MAC address of FF:FF:FF:FF or so! What a hoax!

Both cannot connect to the ECU of my ZOE, as revealed by the Torque Software.

]]>